Metal equipment can become obscured by dust and debris, making it difficult for miners to see what they are doing Metal equipment can become obscured by dust and debris, making it difficult for miners to see what they are doingfiberglass mining equipment. Fiberglass, however, is much less susceptible to this problem, providing clear visibility even in the most challenging conditions.
With the increasing use of hook mesh, the method of bridge rail is also different. The height of the outer railing of the walkway or seat belt should not be lower than 1.10 meters. The net distance between railings should not be greater than 140 mm and horizontal bar rails should not be used. The planning of the hook mesh is necessary to be safe and reliable, the bolt should be installed on the basis of the railing, its strength should meet the requirements of the standard.
Many people do not know how to choose high quality cut wire, I will give us a detailed introduction. The raw material of cutting wire is divided into: stainless steel cutting wire, copper cutting wire, steel wire cutting wire, copper plated steel wire cutting wire, galvanized steel wire cutting wire, iron wire cutting wire, aluminum wire cutting wire and so on.
Ordinary installation of blade thorn rope on the wall and the height of the wall in two meters up and down the general construction costs in a dozen yuan a meter, but if it is said that the height of the prison construction ordinary wall has reached four or five meters so that the construction cost of each meter is about 30 or 40 yuan, mainly because of high altitude operation risk degree is relatively large reason. The construction cost is different, but the price of blade thorn rope is the same, often the construction cost is higher than the product, which is the thorn rope factory recommends customers to use better quality blade thorn rope, which eliminates the cumbersome time and cost of subsequent demolition and installation.
The distance between the adjacent two thorn rope installation do not know whether you have noticed? Careful observation can find that its spacing is not the same, the thorn rope factory for customer consultation when asking the installation height of the reason.
The main difference between the two is the carbon content. The carbon content of iron is 2.11 percent or greater, while the carbon content of steel is 2.11 percent or less. The iron carbon alloy with carbon content above 2.11% is cast iron (pig iron), which is basically not malleable and cannot be drawn into wire. Secondly, the content of impurities is different. The content of harmful impurities such as sulfur and phosphorus in steel is smaller. Steel wire general color focus, iron wire color light point, white point.
Traditional barbed wire is woven into wire, with the development of the economy, the rapid rise of all walks of life, the limitations of the use of traditional barbed wire gradually exposed, such as: aquaculture, to the chicken circle a cage can not be too dense, the wire can not be too thick, woven mesh wire once the mesh over the surface of the net will become soft. We also have the solutions: 1, rolling the straight wire into a wavy shape, but still not enough to feed chickens with mesh can only stretch out the chicken beak can not feed! 2, is electric welding mesh, with the current to the longitude and latitude of the wire spot welding together, mesh do more than most is not restricted.
Material: galvanized silk
4, galvanized can be used zincate galvanized or chloride galvanized process, should use appropriate additives to meet the requirements of this standard coating.
Annealing wire is widely used mainly because it has a good elasticity and flexibility, in the annealing process can be a good control of its hardness and softness, it is mainly made of iron wire, more commonly used in the construction industry tie wire use. So why annealing wire according to material properties processing?
The barbed wire factory will store the inventory of the barbed wire blade in the appropriate place because of the understanding of the product characteristics.
When using these two products, it is obvious that there is a gap between them. By pulling or bending the wire, it is often difficult to restore the original, for example, if the same place is repeatedly bent, it will be found that it has broken, and the cold drawing wire will not. Cold drawing wire compared with iron wire, its hardness, tensile resistance, bending ability is greatly enhanced, suitable for building materials.
4. Keep the rinsing water clean after wire pickling, which is an important link to reduce zinc consumption. The management system of the rinsing water after the steel wire pickling should be regularly and regularly discharged after the rinsing water, and the rinsing water should be kept clean and low acid value as far as possible. The pH control is more appropriate.
The characteristics of hexagonal wire mesh: strong structure, flat surface, with good corrosion resistance, oxidation resistance and so on.
And high quality data and production cost and production conditions are bound, so some welding screen manufacturers did not meet the requirements of this aspect, natural in this case there is no way to improve product strength. In addition to data, and produce process, even if again good data, but the factory did not meet the requirements of production process in welding, also can form the product under the high pressure welding, so it is also a kind of strength on the decline, process conditions of different manufacturers also have very big difference, so it formed a shopping mall on the above products are differences of strength.
Cold galvanized is in the plating tank through the current unidirectional zinc gradually plated on the metal surface, production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust. Compared with electrogalvanizing, hot galvanizing has lower production cost and less impact on the environment than electroplating.