Our FRP manufacturers in China have more choices for resins selection, and the local production of AOC resins also decreased the supply time and cost.
FRP’s advantages such as corrosion resistance, light weight, high strength, maintenance free, cost-effective, rich color, etc. make FRP products are the hot products liked by many different industries.
The lack of clear regulations and controls explains that P25TiO2NPs are still found in many of the commercialized sunscreens in the market. Some of them are coated to reduce the photoactivity of the anatase form, which is known to be responsible for tissue damage, but not enough studies were made on these coated forms. The anatase photoactivity could trigger the production of reactive oxygen species (ROS) generation, as it was stated before. The ROS are chemically reactive species containing oxygen, such as peroxides, superoxide, hydroxyl radical, and singlet oxygen. They are regularly produced in the biological milieu and counterbalanced by physiological antioxidant defense mechanisms. However, an abrupt increase of ROS may result in non-reversible damage to the skin cells. The effects of coated and uncoated P25TiO2NPs need therefore to be studied, and articles on this topic present different conclusions. [11], [12], [13] Recent literature on this topic found that TiO2NPs inhalation provokes serious genotoxicity and DNA damage [14], [15], [16], [17]. On the other hand, some studies in rats have reported no significant harm to genetic material [18], [19], [20], [21], [22].
From studies deemed relevant, the experts found that titanium dioxide as a food additive is poorly absorbed by the gastrointestinal tract of mice and rats, with no adverse effects observed in short-term studies in rodents receiving titanium dioxide in their diets. No observed adverse effect levels (NOAELs) of 15,000 milligrams per kilogram of bodyweight (mg/kg BW) per day and 5,000 mg/kg BW per day—the highest doses tested—were established for mice and rats, respectively.
Health advocates urge US regulators to ban common food coloring additive, by Tom Perkins, The Guardian, June 2, 2023
According to the feedback of manufacturers, the recent mainstream factory new single price, the market as a whole into the center of gravity. On the demand side, the terminal in August is still the off-season, many downstream still have inventory use, the current batch purchase intention is limited, and the market turnover is low. Some plastics and papermaking related downstream feedback part of the signal price is high. Recent titanium dioxide raw material price shock is strong, titanium dioxide price upward support has been enhanced, comprehensive market factors, the current titanium dioxide market into the stable price state after rising.
When it comes to sourcing titanium dioxide, it is essential to understand the various processes involved in its production. The two primary production methods are the sulfate process and the chloride process. The sulfate process tends to be more cost-effective in certain contexts, but it also generates a substantial amount of waste, putting pressure on manufacturers to invest in waste treatment technologies. On the other hand, the chloride process is known for its superior quality and lower environmental impact, albeit at a higher production cost.
In Europe, the downstream paints and coatings sector presented weak demand in front of the titanium dioxide manufacturers, and thus, the titanium dioxide price trend experienced a gradual decline in its trajectory. Additionally, the pressure of inflation and increasing bank interest rates lowered the spending appetite of consumers which had an adverse effect on the titanium dioxide price trends. Further, the export and import of titanium dioxide were also caught under the negative influence of the poor economic conditions of the market.
Natural barite and anthracite containing more than 95% barium sulfate are mixed and fed at a ratio of 3:1 (mass). After being crushed to a diameter of less than 2cm, it enters the reduction furnace. The furnace temperature is controlled to be 1000-1200°C in the front section and 500-500 in the back section. 600°C, the reduction furnace rotates at a speed of 80 seconds per revolution, and the reaction conversion rate is 80% to 90%.
Lithopone was discovered in the 1870s by DuPont. It was manufactured by Krebs Pigments and Chemical Company and other companies.[2] The material came in different seals, which varied in the content of zinc sulfide. Gold seal and Bronze seals contain 40-50% zinc sulfide, offering more hiding power and strength.[3] Although its popularity peaked around 1920, approximately 223,352 tons were produced in 1990. It is mainly used in paints, putty, and in plastics.[1]
Despite its many advantages, the production of lithopone is not without its challenges. The raw materials used to make lithopone, particularly zinc sulfide, can be expensive and difficult to source. In addition, the production process itself can be complex and energy-intensive, requiring specialized equipment and skilled workers to operate. As a result, lithopone manufacturers must carefully manage their operations to ensure they remain competitive in the market.
4.3 g/Cm3
The ingredient in question? Titanium dioxide.
BaSO4+C→BaS+4CO
Total zinc and barium sulphate