Good Quality FRP Winding Machine - Mandrels and Molds – Jrain
Good Quality FRP Winding Machine - Mandrels and Molds – Jrain Detail:
Jrain offers a wide range of mandrels and molds.
Pipe mandrels and cylinder tank molds, together with the winding machine, are mainly used to make the fiberglass pipe and tanks. The molds rotate and then the winding machine will wind the fiberglass onto the molds.
Other molds for fittings are mainly used for hand lay-up process.
Normally, pipe mandrels are made of pure steel or steel with FRP, and tank molds and fittings molds are made of steel. These mandrels and molds are with high durability.
Smooth surface together with a certain of taper and the demolding agent make the demolding process easy, and save a lot of labor and time, and increase the product quality.
Steel pipe mandrel can realize:
Wall thickness: >=7mm
Taper: +/-1.0mm
Steel + FRP pipe mandrel can be used for longer time, as the steel structure give strong support and the FRP surface can be repaired for small defects.
Our mandrels and molds are conformed to national standards. They are with high accuracy and not easy to deform, and as a result, can serve for longer time.
The pipe mandrel can be used for producing the following connection type: plain ends, adhesive bonded, rubber seal lock joint and rubber seal joint, bell and spigot joint, etc.
Except the normal molds, Jrain provides contractile molds also.
Other special molds are available upon request.
Jrain’s mandrels and molds supplied shall be of the best quality, completely new and reliable and the type selection complies with requirement of process technology as well as normal and safe operation and their long term service.
Product detail pictures:
Related Product Guide:
The customer satisfaction is our primary goal. We uphold a consistent level of professionalism, quality, credibility and service for Good Quality FRP Winding Machine - Mandrels and Molds – Jrain , The product will supply to all over the world, such as: Southampton, Stuttgart, Bolivia, With the development and enlargement of mass clients abroad, now we have set up cooperative relationships with many major brands. We have our own factory and also have many reliable and well-cooperated factories in the field. Adhering to the "quality first, customer first, We are provideing high-quality, low-cost products and first-class service to customers. We sincerely hope to establish business relationship with customers from all over the world on the basis of quality, mutually benefit. We welcome OEM projects and designs.
By Ricardo from Gabon - 2017.03.28 16:34
We have been engaged in this industry for many years, we appreciate the work attitude and production capacity of the company, this is a reputable and professional manufacturer.
By Novia from Florida - 2017.12.09 14:01
Related products
-
Chinese Professional GRP Grating - Gratings &a...
Jrain panels are molded in one piece and feature a concave non-slip walking surface. The cost effective panels allow for efficient on-site cutting to minimize grating waste and load bearing bars in both directions allow for use without continuous side support. Jrain’s molded fiberglass grating is significantly lighter in weight than metallic gratings and the high resin content provides excellent corrosion resistance and requires very little maintenance. A higher safety factor is achieve...
-
factory Outlets for Fiberglass Stack Liner - C...
Because of many advantages like below, fiberglass car and boat are very hot products recently in many industries such as transportation, building, electronics, toy cars, yacht, fishing and so on. In addition, as the development of environmental protection awareness, almost every country limit the trees cutting, which pushed the fiberglass boats manufacturing as the fiberglass is the ideal material to construct the middle and small boats. The related accessories for fiberglass cars include bum...
-
Good quality Fiberglass Sewer Pipe - Piping Sy...
Fiberglass pipes include pure fiberglass pipes, sand pipes, insulation pipe, dual laminate pipe (with PVC, CPVC, PE, PP, PVDF, etc.) and so on The wall construction of a fiberglass pipe system consists of three layers: 1． Liner: determines the optimal resistance to the medium. 2． Structural layer: provides high mechanical strength and resistance to loads. 3． Top coat: protects the piping system from weather, chemical penetration and UV radiation. They are very popular in many industries be...
-
Manufacturer for GRP Pipes and Fittings for Shi...
Fiberglass fittings are generally made of hand lay-up process, with high resin content. Different shapes can be realized by using molds. Different resins can be selected for different medium and service conditions. Any special fittings on sizes and shapes will be available upon request. Fiberglass fittings are very popular as they are featured by: • Great strength in relation to the weight • Electrical and thermal insulation • Resistant to corrosion and chemicals • Resistant to the influences...
-
Cheap price Frp Fuel Tank - Insulation Tanks &...
Should insulation be required, it is a simple task to equip the tanks with a 50mm PU foam layer covered by a 5mm FRP layer. This method of insulation produces a K value of 0.5W/m2K. If needed the thickness can be adjusted, for example to 100mm PU foam (0.3W/m2K). But the thickness of insulation is generally to be 30-50mm, while the thickness of outer protection cover can be 3-5mm. FRP tank is strength higher than that of steel, casting iron, plastic and so on. Therefore, by combining the insu...
-
Chinese wholesale GRP Cover - Steps – Jrain
Fiberglass stair tread is used not only by housing estates but also by many factories because of anti-corrosion performance, such as water treatment, chemical plants, petroleum industry, textile mill, power plant, sea food processing plant, beverage industry, ship steps, paper and pulp factory, etc. Stair Tread Thickness Mesh Panel Size Maximum Span for 300lbs. (136kg) at Mid-Span Panel Weight Open Area 1/8” (3.2mm) or less deflection 1/4” (6.4mm) or less deflection 1-1/2” ...
